Home > News > Precautions for using powder mixer v-mixer v-type dry powder blender

Precautions for using powder mixer v-mixer v-type dry powder blender


2020-12-02


Powder mixer v-mixer v-type dry powder blender has a unique mixing cylinder structure, high mixing efficiency, no dead ends, cylinders, and supports. For special materials, the cylinder can be made of plastic. It is specially made for materials that cannot be in contact with metal and strong corrosive materials. The inner and outer walls are polished, the appearance is beautiful, the mixing is uniform, and the use is wide. Comply with GMP standard, and can be equipped with compulsory mixer according to user requirements.

Working principle of powder mixer v-mixer v-type dry powder blender

Powder mixer v-mixer v-type dry powder blender adopts manual feeding and closed disc valve discharging structure, which can implement the dust-free operation. At the same time, the material is mixed without mechanical extrusion and strong friction, which can keep the material particles intact. The mixing barrel of this machine is made of stainless steel, which does not pollute the mixture. In addition, the machine is also equipped with a timing device to control the mixing time of materials.

Use of powder mixer v-mixer v-type dry powder blender

Powder mixer v-mixer v-type dry powder blender is an unequal height mixing barrel formed by cutting the barrel at a 40-degree angle, so it has a better mixing effect than the general W-type mixer. The center is supported by the second box of the base. axis. When working, the material bucket rotates around the same horizontal axis from the same rotation speed, so that the material is continuously turned up and down in combination-separation, separation-closure. The barrel is made of stainless steel, polished inside and outside, and the surface is smooth, which reduces the adhesion of materials, guarantees the quality of the mixture, and reduces the cleaning work after the operation. Powder Mixer v-mixer V-type dry powder blender adopts electromagnetic speed-regulating motor, the speed can be steplessly adjusted between 2-15 rpm according to operation needs, and the reducer is a single-head worm or cylindrical gear with self-locking Features. The electrical control adopts energy-consumption braking, and there is a thermal relay to protect the motor from overload. The length of the mixing time is controlled by a time delay. In addition, the circuit also uses a speedometer to rotate to control the position of unloaded products after shutdown. This machine can be equipped with a W type reciprocating vacuum pump and SZ type water ring vacuum pump to realize vacuum feeding and improve working conditions.

For the mixing of finer powder, agglomerates, or materials with a certain amount of water, according to the special requirements of users, a mandatory mixing device can be installed in the mixing tank to disperse the materials during the mixing process, thereby shortening the mixing time, So that the materials are mixed more evenly.

Precautions for using powder mixer v-mixer v-type dry powder blender

1. A dry run test run should be carried out before use. Before the test run, check the firmness of all the connections of the horizontal V-type mixer, the amount of lubricating oil in the reducer, and the integrity of the electrical equipment, and then close the main switch. Turn on the power supply and conduct a dry run test run.
2. Powder mixer v-mixer v-type dry powder blender installation: Place the machine steadily, install the machine feet, and level it so that the machine can run freely.
3. Before use, add oil to the place that needs to be refueled and then perform a no-load operation to check whether the fasteners are loose, whether the electrical appliances are normal, and whether the machinery is operating normally. If there is any abnormality, perform repair and debugging.
4. Turn the feeding port to the top, open the feeding cover to feed, and the amount of feeding should not exceed the specified volume, then close the feeding cover and start the machine to run. If abnormalities are found on the way, it must be shut down for inspection.
5. The inside and outside of the hopper must be rinsed clean after getting off work or when changing types.

 

Send your message to this supplier

*From:
*To:
Mr Lio
*Message:

Enter between 20 to 4,000 characters.

This is not what you are looking for? See all products

Want to get quotations

  • Name *
  • E-mail *
  • Tel
  • Country
  • Message *
x